Any Questions?
Feel Free to Email Us at
Orders@brewgadgets.com
|
| Kegging |
Home Brew Kegging Kit |
This Equipment Setup Allows the home brewer to easily dispense, store 5 gallon batches of homebrew with less mess and time than with bottles. With this equipment setup you will have everything you need to dispense your home brew very own homebrew. Portable so you can take this equipment to other parties and share your handcrafted beer. This setup includes:
|
With Refurbished Keg $186.99 Without Refurbished Keg $156.99 |
Home Brew Refrigerator Conversion Kit  |
Complete with ball lock disconnects, includes faucet,knob, shank, regulator CO2 tank (empty), hoses, fittings and stainless steel drip tray. (Keg not included) | $224.99 |
5 Gallon Reconditioned Ball Lock Keg  |
These affordable kegs are reconditioned with new seals where needed and sanitized. These kegs have been pressure tested before leaving our store, and so are capable of holding pressure. They are used kegs and will have dents, dings, and scratches that are only cosmetic and do not harm the functionality of the keg. If you are concerned about the condition of the o-rings those may be purchased separately. It's a good idea to have an extra set on hand in the event that any of the o-rings tear during use. Kegging beer is so much quicker and cleaner than bottling You will wonder why you didn't start kegging your beer sooner! |
$34.99 |
Squeeze Valve Dispenser  |
Plastic Liquid Dispenser Tap: The economical choice. Simple construction ensures that valve only opens when it is squeezed. 3/16" tubing will fit, just heat it with boiling water prior to assembly; no clamp needed. | $2.95 |
Bevlex Tubing 1/4" I.D. x 1/2" O.D
|
Bevlex 200 Tubing Great for Gas or Liquid side Major Brewery Approved If the taste of your beer and the operation of your draft system is important to you, this is the only beer tubing you should consider. It's special dual-durometer construction combines a low extraction inner contact surface with a flexible outer layer for excellent kink resistance and taste protection properties. |
$0.49 Per Foot |
One Column Beer Tower  |
This Column Standard comes complete with all parts and ready to install. It is a 3” Chrome Single Faucet and is 12” high It includes the faucets. 5ft. of 3/16 ” tubing with tailpieces, hex nuts and washers. It has Styrofoam insulated barrels to prevent sweating. Faucet Handles are sold separately. Usually ships within 3-4 days. |
$94.00 |
Two Column Beer Tower  |
This Double Faucet Column Standard comes complete with all parts and ready to install. It is a 3” Chrome Double Faucet and is 12” high It includes the faucets. 5ft. of 3/16 ” tubing with tailpieces, hex nuts and washers. It has Styrofoam insulated barrels to prevent sweating. Faucet Handles are sold separately. Usually ships within 3-4 days. |
$130.00 |
Three Column Beer Tower  |
This Triple Faucet Column Standard comes complete with all parts and ready to install. It is a 3” Chrome Triple Faucet and is 12” high It includes the faucets. 5ft. of 3/16 ” tubing with tailpieces, hex nuts and washers. It has Styrofoam insulated barrels to prevent sweating. Faucet Handles are sold separately. Usually ships within 3-4 days. |
$186.00 |
Tap-Rite Dual Gauge Regulator |
This CO2 regulator delivers up to 60 PSI of dispensing pressure. It has two gauges: one 0-60 PSI gauge, which displays dispensing pressure, and one 0-2000 PSI gauge, which displays the pressure remaining in the CO2 cylinder. A relief valve is built into the regulator body for safety. The gas outlet contains a shutoff valve, which allows you to instantly turn off the pressure to your kegs. | $47.00 |
Sanke Keg Tap |
NADS Blue Handle Tap
|
$34.79 |
Tail Piece 1/4" Barbed |
Nickle Plated Brass Standard Beer Tail Piece 1/4" Barbed | $0.80 Each |
Hex Nut for Tail Piece |
Economy Beer Line Hex Nut | $0.84 Each |
Stainless Steel Adjustable Clamp  |
Adjustable with a screwdriver 1/4" to 7/8" | $0.69 Each |
Three Way Air Distributor |
An air distributor works for dispensing CO2 to numerous kegs when there is no need to control individual output pressure.
|
$43.02 |
Ball Lock Gas Barbed |
Gas Side Ball Lock Disconnect - 1/4" Barbed - 30 Degree Angle |
$4.70 |
Ball Lock Liquid Barbed
| Liquid Side Ball Lock Disconnect - 1/4" Barbed - 30 Degree Angle |
$4.70 |
| Ball Lock Gas Threaded
| Gas Side Ball Lock Disconnect - 1/4" MFL- 30 Degree Angle Note: Picture of Barbed |
$6.69 |
Ball Lock Liquid Threaded
| Liquid Side Ball Lock Disconnect - 1/4" MFL - 30 Degree Angle Note: Picture of Barbed |
$6.39 |
Pin Type Gas Barbed 
| Gas Side Pin Type Disconnect - 1/4" Barbed - 30 Degree Angle | $4.99 |
Pin Type Liquid Barbed 
| Liquid Side Pin Type Disconnect - 1/4" Barbed - 30 Degree Angle | $4.99 |
Replacement O-ring set |
All the gaskets you will need to refurbish a used Cornelius keg. | $3.89 |
Analog Temperature Controller |
Use this analog unit to control the temperature of a refrigerator, freezer, or air conditioner. This unit has a 4° swing on it, and a temperature range of 20° to 80° F. | $53.99 |
Cornelius Keg CO2 Charger  |
Take your homebrew on the road without hauling around the CO2 tank and all those hoses. The Keg Charger is a simple portable device for replacing the CO2 pressure as you dispense beer. Attaches a standard 1/4" MFL gas side threaded not barbebed quick disconnect. The trigger valve gives you complete control on the pressure level without a regulator. For dispensing only, will not force carbonate. Includes one 16 gram non-threaded cartridge. | $15.99 16 Gram Refill Cartridges $1.00 |
Lakeview Jaycees
